|
Details, datasheet, quote on part number:TPS72115
| |
Datasheet text preview:
www.ti.com
Actual Size (3,00 mm x 3,00 mm)
TPS72101, TPS72115 TPS72116, TPS72118
SLVS352B DECEMBER 2001 REVISED MAY 2002
LOW INPUT VOLTAGE, CAP FREE 150-mA LOW-DROPOUT LINEAR REGULATORS
FEATURES D 150-mA LDO D Available in 1.5-V, 1.6-V, 1.8-V Fixed-Output
and Adjustable Versions voltage (150 mV at full load). Therefore, compared to many other regulators that require 2.5-V or higher input voltages for operation, these regulators can be operated directly from two AAA batteries. Also, the typical quiescent current (ground pin current) is low, starting at 85 µA during normal operation and 1 µA in shutdown mode. These regulators can be operated very efficiently and, in a battery-powered application, help extend the longevity of the device. Similar LDO regulators require 1-µF or larger output capacitors for stability. However, this regulator uses an internal compensation scheme that stabilizes the feedback loop over the full range of input voltages and load currents with output capacitances as low as 0.1-µF. Ceramic capacitors of this size are relatively inexpensive and available in small footprints. This family of regulators is particularly suited as a portable power supply solution due to its minimal board space requirement and 1.8-V minimum input voltage. Being able to use two off-the-shelf, AAA, batteries makes system design easier and also reduces component cost. Moreover, the solution will be more efficient than if a regulator with a higher input voltage is used.
DBV PACKAGE (TOP VIEW) IN GND EN 1 2 3 4 NC/FB 5 OUT
D Low Input Voltage Requirement
(Down to 1.8 V)
D Small Output Capacitor, 0.1-µF D Dropout Voltage Typically 200 mV at 150 mA D Less Than 1 µA Quiescent Current in
Shutdown Mode
D Thermal Protection D Over Current Limitation D 5-Pin SOT-23 (DBV) Package APPLICATIONS D D D D D D D D D
Portable Communication Devices Battery Powered Equipment PCMCIA Cards Personal Digital Assistants Modems Bar Code Scanners Backup Power Supplies SMPS Post Regulation Internet Audio
DESCRIPTION
The TPS721xx family of LDO regulators is available in fixed voltage options that are commonly used to power the latest DSP's and microcontrollers with an adjustable option ranging from 1.22 V to 2.5 V. These regulators can be used in a wide variety of applications ranging from portable, battery-powered equipment to PC peripherals. The family features operation over a wide range of input voltages (1.8 V to 5.5 V) and low dropout
1.8 V
TPS72115 IN EN OUT GND
1.5 V
0.1 µF
0.1 µF
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
Copyright 2002, Texas Instruments Incorporated
TPS72101, TPS72115 TPS72116, TPS72118
SLVS352B DECEMBER 2001 REVISED MAY 2002
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
TJ VOLTAGE Adjustable 40°C to 125°C to 125°C 1.5 V 1.6 V SOT-23 (DBV) PACKAGE PART NUMBER TPS72101DBVT(1) TPS72115DBVT(1) TPS72116DBVT(1) TPS72118DBVT(1) TPS72101DBVR(2) TPS72115DBVR(2) TPS72116DBVR(2) TPS72118DBVR(2) SYMBOL PEKI PEII PHFI PEJI
1.8 V (1) The DBVT indicates tape and reel of 250 parts. (2) The DBVR indicates tape and reel of 3000 parts.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted(1) TPS72101, TPS72115 TPS72116, TPS72118 Input voltage range(2) Voltage range at EN Voltage on OUT, FB, NC Peak output current ESD rating, HBM Continuous total power dissipation Operating virtual junction temperature range, TJ 0.3 V to 7 V 0.3 V to 7 V 0.3 V to VI + 0.3 V Internally limited 3 kV See Dissipation Rating Table 40°C to 150°C
Storage temperature range, Tstg 65°C to 150°C (1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. (2) All voltage values are with respect to network ground terminal.
PACKAGE DISSIPATION RATING
BOARD Low K(1) High K(2) PACKAGE DBV DBV RJC 65.8 °C/W 65.8 °C/W RJA 259 °C/W 180 °C/W DERATING FACTOR ABOVE TA = 25°C 3.9 mW/°C 5.6 mW/°C TA 25°C POWER RATING 386 mW 555 mW TA = 70°C POWER RATING 212 mW 305 mW TA = 85°C POWER RATING 154 mW
222 mW (1) The JEDEC Low K (1s) board design used to derive this data was a 3 inch x 3 inch, two-layer board with 2 ounce copper traces on top of the board. (2) The JEDEC High K (2s2p) board design used to derive this data was a 3 inch x 3 inch, multilayer board with 1 ounce internal power and ground planes and 2 ounce copper traces on top and bottom of the board.
2
www.ti.com
TPS72101, TPS72115 TPS72116, TPS72118
SLVS352B DECEMBER 2001 REVISED MAY 2002
ELECTRICAL CHARACTERISTICS
over recommended operating free-air temperature range VI = VO(typ) + 1 V, IO= 1 mA, EN = VI, Co = 1 µF (unless otherwise noted) PARAMETER VI IO TJ Input voltage(1) Continuous output current Operating junction temperature TPS72101 TPS72115 VO Output voltage TPS72116 TPS72118 0 µA< IO < 150 mA,(1) TJ = 25°C 0 µA< IO < 150 mA, TJ = 25°C 0 µA< IO < 150 mA, TJ = 25°C 0 µA< IO < 150 mA, TJ = 25°C I(Q) Quiescent current (GND current) current (GND current) IO = 150 mA, IO = 150 mA EN < 0.5 V, Standby current current Vn Vref PSRR Output noise voltage Reference voltage Ripple rejection Current limit Output voltage line regulation (VO/VO)(3) Output voltage load regulation VIH VIL II VDO In EN high level input EN low level input EN = 0 V EN i input current t t (4) Dropout voltage (4) lt Feedback input current TPS72118 TPS72101 TPS72101 170 20 EN = IN IO = 150 mA, IO = 150 mA, TJ = 25°C 1.2 V VO 5.2 V TPS72118 TPS72115 EN < 0.5 V BW = 200 Hz to 100 kHz, TJ = 25°C, TJ = 25°C f = 100 Hz, Co = 10 µF, IO = 150 mA, See Note 2 VO + 1 V < VI 5.5 V 55 0 < IO < 150 mA, Co = 1 µF 90 1.225 TJ = 25°C, See Note 1 175 TJ = 25°C 0.03 48 525 0.09 0.1 TJ = 25°C 1.4 0.2 0.01 0.01 150 240 1 1 Thermal shutdown temperature Thermal shutdown hysteresis (1) Minimum IN operating voltage is 1.8 V or VO(max) + VDO (max load), whichever is greater. (2) Test condition includes, output voltage VO=1 V and pulse duration = 10 mS. (3) VImin = (VO + 1) or 1.8 V whichever is greater. °C °C mV µA 0.4 V µA 0.5 %/V mV TJ = 25°C TJ = 25°C 1.8 V VO 2.5 V 2.5 V VI 5.5 V 2.6 V VI 5.5 V 2.8 V VI 5.5 V TEST CONDITIONS MIN 1.8 0 40 0.97 VO 1.5 1.455 1.6 1.552 1.8 1.746 85 120 570 850 0.01 1 µA µV V dB mA µA 1.854 1.648 1.545 V TYP MAX 5.5 150 125 1.03 VO UNIT V mA °C
Line regulation (mV) + % V
V
O
5.5 1 * V Imin V
00
1000
(4) Dropout voltage is defined as the differential voltage between VO and VI when VO drops 100 mV below the value measured with VI = VO + 1 V.
3
|
|
