Details, datasheet, quote on part number: S24023PAT
PartS24023PAT
CategoryPower Management => Supervisory Circuits => System Supervisors/Reset => Precision Reset
TitlePrecision Reset
DescriptionPrecision Reset Controller And 2k I2C™ Memory With Both Active High And Active Low Reset Outputs
CompanySummit Microelectronics, Inc.
DatasheetDownload S24023PAT datasheet
  

 

Features, Applications

Precision RESET Controller and 2K I2C Memory With Both RESET and RESET Outputs

FEATURES Precision Supply Voltage Monitor Dual reset outputs for complex microcontroller systems Integrated memory write lockout Guaranteed RESET (RESET) assertion to VCC=1V Power-Fail Accuracy Guaranteed No External Components 3 and 5 Volt system versions Low Power CMOS Active current less than 3mA Standby current less than 25ľA Memory Internally Organized X 8 Two Wire Serial Interface (I2CTM) ­ Bidirectional data transfer protocol ­ Standard 100KHz and Fast 400KHz

High Reliability Endurance: 1,000,000 erase/write cycles Data retention: 100 years 8-Pin PDIP or SOIC Packages

OVERVIEW The S24022 and S24023 are power supervisory devices with 2,048 bits of serial E2PROM. They are fabricated using SUMMIT's advanced CMOS E2PROM technology and are suitable for both 3 and 5 volt systems. The memory is internally organized 8. It features the I2C serial interface and software protocol allowing operation on a simple two-wire bus. The S24022 provides a precision VCC sense circuit and two open drain outputs: one (RESET) drives high and the other (RESET) drives low whenever VCC falls below VTRIP. The S24023 is identical to the S24022 with the exception being RESET is not bonded out on pin 7.

PIN CONFIGURATIONS RESET - RESET is an active low open drain output. It is driven low whenever VCC is below VTRIP. RESET is also an input and can be used to debounce a switch input or perform signal conditioning. The RESET pin does have an internal pull-up and should be left unconnected if the signal is not used in the system. However, when the pin is tied to a system RESET line an external pull-up resistor should be employed. RESET - RESET is an active high open drain output. It is driven high whenever VCC is below VTRIP. RESET is also an input and can be used to debounce a switch input or perform signal conditioning. The RESET pin does have an internal pull-down and should be left unconnected if the signal is not used in the system. However, when the pin is tied to a system reset line an external pull-down resistor should be employed. ENDURANCE AND DATA RETENTION

PIN NAMES SDA SCL RESET & RESET VSS VCC NC Serial Data I/O Serial Clock Input Reset Output Ground Supply Voltage No Connect

The S24022/23 is designed for applications requiring 1,000,000 erase/write cycles and unlimited read cycles. It provides 100 years of secure data retention, with or without power applied, after the execution of 1,000,000 erase/write cycles. APPLICATIONS Reset Controller Description The S24022/23 provides a precision RESET controller that ensures correct system operation during brown-out and power-up/-down conditions. It is configured with two open drain RESET outputs; pin is an active high output and pin is an active low output. During power-up, the RESET outputs remain active until VCC reaches the VTRIP threshold and will continue driving the outputs for approximately 200ms after reaching VTRIP. The RESET outputs will be valid so long as VCC > 1.0V. During power-down, the RESET outputs will begin driving active when VCC falls below VTRIP. The RESET pins are I/Os; therefore, the S24022/23 can act as a signal conditioning circuit for an externally applied reset. The inputs are edge triggered; that is, the RESET input will initiate a reset timeout after detecting a low to high transition and the RESET input will initiate a reset timeout after detecting a high to low transition. Refer to the applications Information section for more details on device operation as a reset conditioning circuit.

PIN DESCRIPTIONS Serial Clock (SCL) - The SCL input is used to clock data into and out of the device. In the WRITE mode, data must remain stable while SCL is HIGH. In the READ mode, data is clocked out on the falling edge of SCL. Serial Data (SDA) - The SDA pin is a bidirectional pin used to transfer data into and out of the device. Data may change only when SCL is LOW, except START and STOP conditions. is an open-drain output and may be wireORed with any number of open-drain or open-collector outputs. No Connects (NC) the no connect pins may be left floating or tied to ground. They cannot be tied high.

FIGURE 1. TYPICAL SYSTEM CONFIGURATION FOR DUAL RESET

 

Related products with the same datasheet
S24022P-2.7
S24022P-2.7T
S24022P-A
S24022P-AT
S24022P-B
S24022P-BT
S24022P2.7
S24022P2.7T
S24022PA
S24022PAT
S24022PB
S24022PBT
Some Part number from the same manufacture Summit Microelectronics, Inc.
S24023PB Precision Reset Controller And 2k I2C™ Memory With Both Active High And Active Low Reset Outputs
S24042 Precision Reset Controller And 4k I2C™ Memory With Both Active High And Active Low Reset Outputs
S24163 Precision Reset Controller And 16k-bit Memory With Active Low Reset
S39421 General Purpose Hot Swap Controller
S4242 Precision Voltage Supervisory Circuit With 4k I2C™ Memory
S9318 Single 8-Bit Up/dn Count Nonvolatile DACPOT™
S93462 Precision Supply-voltage Monitor And Reset Controller (Organized X8)
S93662
 
0-C     D-L     M-R     S-Z