Details, datasheet, quote on part number: M28C16-300MS6T
Description16K (2K x 8) LOW Voltage Parallel Eeprom with Software DATA Protection
CompanyST Microelectronics, Inc.
DatasheetDownload M28C16-300MS6T datasheet


Features, Applications

FAST ACCESS TIME: 200ns SINGLE LOW VOLTAGE OPERATION LOW POWER CONSUMPTION FAST WRITE CYCLE: ≠ 64 Bytes Page Write Operation ≠ Byte or Page Write Cycle: 3ms Max ENHANCED END OF WRITE DETECTION: ≠ Data Polling ≠ Toggle Bit PAGE LOAD TIMER STATUS BIT HIGH RELIABILITY SINGLE POLYSILICON, CMOS TECHNOLOGY: ≠ Endurance >100,000 Erase/Write Cycles ≠ Data Retention >40 Years JEDEC APPROVED BYTEWIDE PIN OUT SOFTWARE DATA PROTECTION M28LV16 is replaced by the products described on the document M28C16A DESCRIPTION The x 8 low power Parallel EEPROM fabricatedwith SGS-THOMSON proprietary single polysilicon CMOS technology. The device offers fast access time with low power dissipation and requires to 3.6V power supply. The circuit has been designed to offer a flexible microcontroller interface featuring both hardware and software handshaking with Data Polling and Toggle Bit. The M28LV16 supports 64 byte page write operation. A Software Data Protection (SDP) is also possible using the standard JEDEC algorithm. Table 1. Signal Names

G RB VCC VSS Address Input Data Input / Output Write Enable Chip Enable Output Enable Ready / Busy Supply Voltage Ground

Note: * RB function is offered only with TSOP28 package.
This is information on a product still in production bu t not recommended for new de sign.

Parameter Ambient Operating Temperature Storage Temperature Range Supply Voltage Input/Output Voltage Input Voltage Electrostatic Discharge Voltage (Human Body model)

Note: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the SGS-THOMSON SURE Program and other relevant quality documents. 2. 100pF through MIL-STD-883C, 3015.7

Mode Standby Output Disable Write Disable Read Write

PIN DESCRIPTION Addresses (A0-A10). The address inputs select an 8-bit memory location during a read or write operation. Chip Enable (E). The chip enable input must be low to enable all read/write operations. When Chip Enable is high, power consumption is reduced. Output Enable (G). The Output Enable input controls the data output buffers and is used to initiate read operations. Data In/ Out - DQ7). Data is written to or read from the M28LV16 through the I/O pins. Write Enable (W). The Write Enable input controls the writing of data to the M28LV16. Ready/Busy (RB). Ready/Busy is an open drain output that can be used to detect the end of the internal write cycle. It is offered only with the TSOP28 package. The reader should refer to the M28LV17 datasheet for more information about the Ready/Busy function.

OPERATION In order to prevent data corruption and inadvertent write operations during power-up, a Power On Reset (POR) circuit resets all internal programming cicuitry. Access to the memory in write mode is allowed after a power-up as specified in Table 7. Read The M28LV16 is accessed like a static RAM. When E and G are low with W high, the data addressed is presented on the I/O pins. The I/O pins are high impedance when either E is high. Write operations are initiated when both W and E are low and G is high.The M28LV16 supports both E and W controlled write cycles. The Address is latched by the falling edge or W which ever occurs last and the Data on the rising edge or W which ever occurs first. Once initiated the write operation is internally timed until completion.


Related products with the same datasheet
Some Part number from the same manufacture ST Microelectronics, Inc.
M28C16-300N1T 16K (2K x 8) LOW Voltage Parallel Eeprom with Software DATA Protection
STDS75DS2F Digital Temperature Sensor and Thermal Watchdog
STM1811L Low Power Reset Circuit
L5987ATR 3 A Step-down Switching Regulator
SM6T27AY Transiltm
TSV635AIPT Rail-to-rail Input/output 60 •žA 880 kHz Operational Amplifiers
L6730DTR Adjustable Step-down Controller with Synchronous Rectification
M5474HC564 Octal D-type FLIP FLOP WITH 3 State Output Hc564 Inverting - Hc574 NON Inverting
L6726A_07 Single Phase PWM Controller
LM2902YD Low Power quad Operational Amplifier
TS235 Ts135 thur Ts1235 Thyristors
M54HC132D1 Rad-hard DUAL 2 TO 4 Decoder/demultiplexer
P120NF10 N-channel 100V - 0.009ohm - 110A - To-247 - To-220 - D2pak Stripfet2 Power Mosfet
MD2310FX High Voltage NPN Power Transistor for Standard Definition CRT Display
STM809LW16F Reset Circuit
ST7162N Universal Programmable DUAL PLL
TDA9203 I2C BUS Controlled 70mhz RGB Preamplifier
TLC381B Triacs
Z0607MA Standard 0.8 A Triacs

L7820CD2T : Positive Voltage Regulators

ST92T163V : 8/16-bit Full Speed Usb MCU For Composite Devices With 16 Endpoints, 20k ROM, 2k RAM, I2c, Sci, & MFT

TS486ID : Stereo Headphone Amplifier With Standby Active Low

TSIXXB1 : ASD for Telecom Wireline Terminal Set Interface Protection And Diode Bridge

M24C02-RMN6TP : 16kbit, 8kbit, 4kbit, 2kbit and 1kbit Serial I2C Bus Eeprom

M29F100BB-120M3T : 1 Mbit 128kb x8 or 64Kb x16, Boot Block Single Supply Flash Memory

M28W320ECB85ZB1T : 32mbit (2Mb x16) and 64mbit (4Mb x16) 3V Supply, Uniform Block, Secure Flash Memories

PSD813F4VA-15JT : 128K X 8 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52 Specifications: Device Type: PIA-GENERAL PURPOSE ; Supply Voltage: 3.3V ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Package Type: PLASTIC, LCC-52 ; Pins: 52 ; Features: RoHS

ST72361AR7T5/XXXTRE : 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 16 MHz ; ROM Type: Flash ; Supply Voltage: 4.5 to 5.5 volts ; I/O Ports: 48 ; Package Type: TQFP, Other, 10 X 10 MM, ROHS COMPLIANT, PLASTIC, TQFP-64 ; Operating Range: Industrial ; Pin Count: 64 ; Operating Temperature: -40 to 85 C (-40 to 185


0-C     D-L     M-R     S-Z