Details, datasheet, quote on part number: TDA8263HN
PartTDA8263HN
CategoryMultimedia => Set-Top Box
DescriptionFully integrated satellite tuner
The direct conversion QPSK demodulator is the front-end receiver dedicated to digital TV broadcasting, satisfying both DVB-S and DBS TV standards. The wide range oscillator (from 950 MHz to 2175 MHz) covers the American, European and Asian satellite bands, as well as the SMA-TV US standard.

The Zero-IF (ZIF) concept discards traditional IF filtering and intermediate conversion techniques.

Gain-controlled amplifiers in the RF guarantee optimum signal level. The variable gain is controlled by the signal returned from the Satellite Demodulator and Decoder (SDD) and applied to pin AGC.

The integrated LNA allows the IC to be directly connected to the LNB output. The LNA can be by-passed by an I²C-bus selectable attenuation, providing a 20 dB extra attenuation in order to handle higher input signal levels of up to 0 dBm per channel.

Connected at the RF input, an RMS level detector provides through I²C-bus read mode the full band input signal level.

The LO quadrature outputs are derived from a high performance integrated LC oscillator.

Its frequency is:(flo)/ = (f xtal)/R . Thanks to the low phase noise performance of the integrated LC oscillator which controls the LO frequency, the synthesizer offers a good performance for phase noise in the satellite band. The step size of the LO output frequency is equal to the comparison frequency.

Control data is entered via the I²C-bus. The bus can be either 5.0 V or 3.3 V, allowing compatibility with most of existing microcontrollers.

An 8-byte frame is required to address the device and to program the main divider ratio, the reference divider ratio, the charge-pump current and the operating mode.

A flag is set when the loop is in-lock, readable during read operations, as well as the Power-on reset flag and RF input level.

The device has four selectable I²C-bus addresses. Applying a specific voltage to pin AS selects an address. This feature gives the possibility to use up to four TDA8263HN ICs in the same system.


Features
Direct conversion QPSK and 8PSK demodulation (ZIF)
3.3 V DC supply voltage (no 30 V required)
950 MHz to 2175 MHz frequency range
High range input level;
-70 dBm to -15 dBm at 75 Ohm (normal mode)
Up to 0 dBm (20 dB attenuation configuration).
Low noise RF input (integrated LNA)
0 dB to 55 dB continuous variable gain on RF input
RF input level detector
Switchable 0 dB to 9 dB additional gain on baseband output amplifier
High AGC linearity (< 0.7 dB/step when used with an 8-bit DAC), AGC controlled voltage between 0.3 V and 3 V
Programmable 5 MHz to 36 MHz 5th-order baseband filters for I and Q paths
Fully integrated PLL frequency synthesizer
Low phase noise fully integrated oscillator
Operation from a 16 MHz crystal or external clock
5 frequency steps from 125 kHz to 2 MHz
Crystal frequency output to drive the demodulator IC
Compatible with 5 V and 3.3 V I²C-bus
Fully compatible and easy to interface with the PS digital satellite demodulators family
32-pin low thermal resistance package.


Applications
Direct Broadcasting Satellite (DBS) QPSK demodulation
Digital Video Broadcasting (DVB) QPSK demodulation
BS digital 8PSK demodulation
DVB-S2 8PSK demodulation.
CompanyPhilips Semiconductors (Acquired by NXP)
DatasheetDownload TDA8263HN datasheet
Quote
Find where to buy
 
  

 

Features, Applications

The direct conversion QPSK demodulator is the front-end receiver dedicated to digital TV broadcasting, satisfying both DVB-S and DBS TV standards. The wide range oscillator (from 950 MHz to 2175 MHz) covers the American, European and Asian satellite bands, as well as the SMA-TV US standard. The Zero-IF (ZIF) concept discards traditional IF filtering and intermediate conversion techniques. Gain-controlled amplifiers in the RF guarantee optimum signal level. The variable gain is controlled by the signal returned from the Satellite Demodulator and Decoder (SDD) and applied to pin AGC. The integrated LNA allows the to be directly connected to the LNB output. The LNA can be by-passed an I2C-bus selectable attenuation, providing 20 dB extra attenuation in order to handle higher input signal levels to 0 dBm per channel. Connected at the RF input, an RMS level detector provides through I2C-bus read mode the full band input signal level. The LO quadrature outputs are derived from a high performance integrated LC oscillator. LO f XTAL Its frequency is: = Thanks to the low phase noise performance of the N R integrated LC oscillator which controls the LO frequency, the synthesizer offers a good performance for phase noise in the satellite band. The step size of the LO output frequency is equal to the comparison frequency. Control data is entered via the I2C-bus. The bus can be either 3.3 V, allowing compatibility with most of existing microcontrollers. An 8-byte frame is required to address the device and to program the main divider ratio, the reference divider ratio, the charge-pump current and the operating mode. A flag is set when the loop is in-lock, readable during read operations, as well as the Power-on reset flag and RF input level. The device has four selectable I2C-bus addresses. Applying a specific voltage to pin AS selects an address. This feature gives the possibility to use up to four TDA8263HN ICs in the same system.

Direct conversion QPSK and 8PSK demodulation (ZIF) V DC supply voltage (no 30 V required) 950 MHz to 2175 MHz frequency range High range input level; x -70 dBm to -15 dBm at 75 (normal mode) to 0 dBm (20 dB attenuation configuration). Low noise RF input (integrated LNA) 55 dB continuous variable gain on RF input RF input level detector Switchable 9 dB additional gain on baseband output amplifier High AGC linearity 0.7 dB/step when used with an 8-bit DAC), AGC controlled voltage between 0.3 V and 3 V Programmable 5 MHz to 36 MHz 5th-order baseband filters for I and Q paths Fully integrated PLL frequency synthesizer Low phase noise fully integrated oscillator Operation from a 16 MHz crystal or external clock 5 frequency steps from 125 kHz to 2 MHz Crystal frequency output to drive the demodulator IC Compatible with 5 V and V I2C-bus Fully compatible and easy to interface with the PS digital satellite demodulators family 32-pin low thermal resistance package.

Direct Broadcasting Satellite (DBS) QPSK demodulation Digital Video Broadcasting (DVB) QPSK demodulation BS digital 8PSK demodulation DVB-S2 8PSK demodulation.

Table 1: Symbol VCC ICC fosc Vo(I/Q)(rms) Quick reference data Parameter supply voltage supply current oscillator frequency absolute quadrature error recommended I and Q output voltage RMS value (QPSK signals) LPF cut-off frequency 5-bit controlled measured at 10 MHz

© Koninklijke Philips Electronics N.V. 2004. All rights reserved.

oscillator phase noise in 100 kHz offset; the satellite band fcomp = 1 MHz synthesizer noise floor in 1 kHz and10 kHz the satellite band offset; fcomp = 1 MHz amplifier gain control range ambient temperature

The product is qualified with an output voltage 550 mV (p-p) differential, however larger values can be used at baseband outputs that might have impact on the product performance. Phase noise in optimal conditions, see related application note.

Noise figure at maximum gain: 8 dB High linearity:
Low synthesizer noise floor: -78 dBc/Hz at 1 kHz and 10 kHz offset with

AGC linearity: < 0.7 dB/step with a 8-bit DAC Maximum I/Q amplitude mismatch: 1 dB Maximum I/Q quadrature mismatch: 5° Symbol rates: from 1 MBd to 45 MBd.

Table 2: Ordering information Package Name TDA8263HN HVQFN32 Description plastic thermal enhanced very thin quad flat package; no leads; 32 terminals; body mm Version SOT617-1 Type number


 

Related products with the same datasheet
TDA8263HN/C1
Some Part number from the same manufacture Philips Semiconductors (Acquired by NXP)
TDA8263HN/C1 Fully integrated satellite tuner The direct conversion QPSK demodulator is the front-end receiver dedicated to digital TV broadcasting, satisfying both DVB-S and DBS TV standards. The wide range oscillator
SA58641 High performance mixer FM IF system with high-speed RSSI The SA58641 is a high performance monolithic FM IF system with high-speed RSSI incorporating a mixer/oscillator, two limiting intermediate frequency
TDA8587J 4 x 25 W BTL power amplifier and multi voltage regulator with power switch The TDA8587J is a combination of a quad Bridge-Tied Load (BTL) power amplifier, a multiple voltage regulator and a power switch.
P89LPC9102 8-bit microcontrollers with accelerated two-clock 80C51 core 1 kB 3 V byte-erasable Flash with 8-bit A/D converter The P89LPC9102/9103/9107 are single-chip microcontrollers in low-cost 10-pin and 14-pin
ISP1761 Hi-Speed Universal Serial Bus On-The-Go controller The ISP1761 is a single-chip Hi-Speed Universal Serial Bus (USB) On-The-Go (OTG) Controller integrated with the advanced Philips Slave Host Controller
BAT54XY Schottky barrier quadruple diode in very small SOT363 package Schottky barrier quadruple diode with an integrated guard ring for stress protection. Two electrically isolated dual Schottky barrier diodes
PEMD14 NPN/PNP resistor-equipped transistors; R1 = 47 kOhm, R2 = open NPN/PNP resistor-equipped transistors. FeaturesBuilt-in bias resistors Simplifies circuit design Reduces component count
PESD1CAN CAN bus ESD protection diode in SOT23PESD1CAN in small SOT23 SMD plastic package designed to protect two automotive Control Area Network (CAN) bus lines from the damage caused by ElectroStatic Discharge
PMEG1030EJ 10 V, 3 A very low Vf MEGA Schottky barrier rectifier in SOD323F packagePlanar Maximum Efficiency General Application (MEGA) Schottky barrier rectifier with an integrated guard ring for stress protection
PMEG3020EJ 30 V, 2 A low Vf MEGA Schottky barrier rectifier in SOD323F packagePlanar Maximum Efficiency General Application (MEGA) Schottky barrier rectifier with an integrated guard ring for stress protection
SC16C754B 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOsThe SC16C754B is a quad universal asynchronous receiver/transmitter (UART) with 64-byte FIFOs, automatic hardware/software flow control,
PH3855L N-channel TrenchMOS(tm) logic level FET Logic level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using TrenchMOS™ technology. FeaturesLogic level threshold
PMEG1020EH 10 V, 2 A ultra low Vf MEGA Schottky barrier rectifier in SOD123F packagePlanar Maximum Efficiency General Application (MEGA) Schottky barrier rectifier with an integrated guard ring for stress protection,
PEMB19 PNP/PNP resistor-equipped transistors; R1 = 22 kOhm, R2 = openPNP/PNP resistor-equipped transistors. FeaturesBuilt-in bias resistors Simplifies circuit design Reduces component count Reduces
SC16C654B 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs and infrared (IrDA) encoder/decoderThe SC16C654B/654DB is a 4-channel Universal Asynchronous Receiver and Transmitter (QUART) used
SC16C554B/554DB 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs The SC16C554B/554DB is a 4-channel Universal Asynchronous Receiver and Transmitter (QUART) used for serial data communications. Its principal
PMF3800SN N-channel TrenchMOS(tm) standard level FET Standard level N-channel enhancement mode Field Effect Transistor (FET) in a plastic package using TrenchMOS™ technology. FeaturesLogic level compatible
TDA9975A Triple 10-bit video converter interface with two HDMI(1) inputs The TDA9975 is a triple 10-bit video converter interface with two HDMI(1) inputs. The IC converts a RGB analog signal into a RGB or YUV (YCbCr)
TDA9975AEL/8/C1
TDA9975AHS/8/C1
TDA9975
Same catergory

BA3870 : . BBS (bass boost system) for radio cassette players The is a bass boost audio IC for radio cassette players. BBS adjusts the base boost to a level appropriate for the volume, achieving a rich sound without distortion. Frequency characteristics can be set externally, enabling system design to meet the needs of the application. FApplications Radio cassette.

HI5702-EV2 : 10-bit, 40 MSPS A/D Converter. The is a monolithic, 10-bit, analog-to-digital converter fabricated in a BiCMOS process. It is designed for high speed applications where wide bandwidth and low power consumption are essential. Its 40 MSPS speed is made possible by a fully differential pipeline architecture which also eliminates the need for an external sample and hold circuit. The HI5702.

LF48410 : 1024 X24-bit Video Histogrammer. The LF48410 is capable of generating histograms and Cumulative Distribution Functions of video images. It may also be used as a look up table, a bin accumulator, a delay memory (delay and subtract also possible), or a single port RAM. The on-chip x 24-bit memory array facilitates histograms of images x 4K pixels with a 10-bit pixel resolution. Once.

LM4892IBP : Boomer Audio Power Amplifiers. LM4892 - 1 Watt Audio Power Amplifier With Headphone Sense, Package: Microsmd, Pin Nb=8.

ML2258 : P Compatible 8-bit A/D Converter With 8-channel Multiplexer. The ML2258 combines an 8-bit A/D converter, 8-channel analog multiplexer, and a microprocessor compatible 8bit parallel interface and control logic in a single monolithic device. Easy interface to microprocessors is provided by the latched and decoded multiplexer address inputs and latched three-state outputs. The device is suitable for a wide range.

NJM2295A : FM IF IC For Remote Keyless Entry System.

NJW1146 : Audio Processor With Bbe. s GENERAL is an audio processor with BBE, which also includes Master volume, Balance, Tone Control, eala(NJRC surround), Mute, and Output 2 filter amplifier. All of internal status and variables are controlled I C BUS. s q Operating Voltage Bus interface q BBE q eala & simulated stereo q Master Volume q Balance qTone Control q Bi-CMOS q Package Outline.

NW812 : Encoder/Decoder. Vga Pcam Engine w/ Integrated Audio A/D. The NW812 from Divio enables a complete high-quality low-cost VGA PCAM solution with integrated Audio A/D. The NW812 integrates a VGA resolution video engine based on Divio's patented JPEG-LiteTM technology, high-fidelity audio A/D, Gold certified USB, and direct interface to low-cost CMOS sensors, for a complete A/V PCAM solution. PCAMs based on the NW812.

TDA7293 : Single Channel. 120v - 100w Dmos Audio Amplifier With Mute/st-by. VERY HIGH OPERATING VOLTAGE RANGE (±50V) DMOS POWER STAGE HIGH OUTPUT POWER (100W @ THD = ±40V) MUTING/STAND-BY FUNCTIONS NO SWITCH ON/OFF NOISE VERY LOW DISTORTION VERY LOW NOISE SHORT CIRCUIT PROTECTED (WITH NO INPUT SIGNAL APPLIED) THERMAL SHUTDOWN CLIP DETECTOR MODULARITY (MORE DEVICES CAN BE EASILY CONNECTED IN PARALLEL TO DRIVE VERY LOW IMPEDANCES).

TDA7440 : Tone Control Digitally Controlled Audio Processor. TONE CONTROL DIGITALLY CONTROLLED AUDIO PROCESSOR INPUT MULTIPLEXER - 4 STEREO INPUTS - SELECTABLE INPUT GAIN FOR OPTIMAL ADAPTATION TO DIFFERENT SOURCES ONE STEREO OUTPUT TREBLE AND BASS CONTROL IN 2.0dB STEPS VOLUME CONTROL IN 1.0dB STEPS TWO SPEAKER ATTENUATORS: - TWO INDEPENDENT SPEAKER CONTROL IN 1.0dB STEPS FOR BALANCE FACILITY - INDEPENDENT MUTE.

TMC2250Ax3 : Matrix Multiplier. Four user-selectable filtering and transformation functions: ­ Triple dot product x 3) matrix multiply ­ Cascadeable 9-tap systolic FIR filter ­ Cascadeable x 3-pixel image convolver ­ Cascadeable x 2-pixel image convolver 50 MHz (20ns) pipelined throughput 12-bit input and output data, 10-bit coefficients 6-bit cascade input and output ports in all filter.

UCB1510DB : Ac97 Digital Modem Codec. The is a single chip, integrated mixed signal telecom codec that can directly be connected to a DAA and supports high speed modem protocols. The general purpose I/O pins provide programmable inputs and/or outputs to the system. The UCB1510 has a serial AClink interface intended to communicate to the system controller. Both the codec input data and codec.

MDE9517D : Digital Decoder for DVB Set-Top Boxes and IDTV Sets highly integrated MPEG-2 decoders for DVB-compliant digital set-top boxes (STBs) and integrated digital television sets (IDTVs). The most recent members of the Micronas MDE family feature an integrated transport stream demultiplexer, a high-performance CPU, MPEG-2 audio and video decoding, and the video,.

LX1725 : AudioMAX The Microsemi LX1725 is part of a new generation of fully integrated stereo class-D amplifiers: 15W+15W. The fully integrated halfbridge output for each channel works with both split and single power supply operation. The outputs can be bridged to run in BTL (Bridge Tied Load) mode. Key : 12Wx2 @ 4Ù THD+N.

SSM2302 : Filterless High Efficiency Class-D Stereo Audio Amplifier Product The SSM2302 is a fully integrated, high efficiency, Class-D stereo audio amplifier. It is designed to maximize performance for mobile phone applications. The application circuit requires a minimum of external components and operates from a single 2.5 V to 5.0 V supply. It is capable of delivering.

TAS5132 : The TAS5132 is an integrated stereo digital amplifier power stage with an advanced protection system. The TAS5132 is capable of driving a 6- bridge-tied load (BTL) at up to 25 W per channel with low integrated noise at the output, low THD+N performance, and low idle power dissipation. A low-cost, high-fidelity audio system can be built using a TI chipset,.

TAS5414 : The TAS5414 and TAS5424 are four-channel digital audio amplifiers designed for use in automotive head units and external amplifier modules. The TAS5414 and TAS5424 provide four channels at 23 W continuously into 4 at less than 1% THD+N from a 14.4-V supply. Each channel can also deliver 38 W into 2 at 1% THD+N. The TAS5414 uses single-ended analog inputs,.

BTA316 : Passivated, new generation, high commutation triacs in a SOT78 plastic package.

AT73C209 : The AT73C209 Analog Companion Power Supply And Audio Interface IC The AT73C209 Analog Companion power supply and audio interface IC is designed for low-cost music players. It supplies the required voltages and currents to all the sections of these portable devices taking energy from a single alkaline battery, and also provides a high-quality audio interface.

OPA1644 : Sound-Plus High-Performance, JFET-Input Audio OpAmps The OPA1641 (single), OPA1642 (dual), and OPA1644 (quad) series are JFET-input, ultralow distortion, low-noise operational amplifiers fully specified for audio applications. The OPA1641, OPA1642, and OPA1644 rail-to-rail output swing allows increased headroom, making these devices ideal for use in any audio.

 
0-C     D-L     M-R     S-Z