|
Details, datasheet, quote on part number:HMU16/883
| |
Datasheet text preview:
®
HMU16/883
16 x 16-Bit CMOS Parallel Multiplier
Description
The HMU16/883 is a high speed, low power CMOS 16 x 16-bit parallel multiplier ideal for fast, real time digital signal processing applications. The 16-bit X and Y operands may be independently specified as either two's complement or unsigned magnitude format, thereby, allowing mixed mode multiplication operations. Additional inputs are provided to accommodate format adjustment and rounding of the 32-bit product. The Format Adjust control allows the user to select a 31-bit product with the sign bit replicated in the LSP. The round control provides for rounding the most significant portion of the result by adding one to the most significant bit of the LSP. Two 16-bit Output Registers (MSP and LSP) are provided to hold the most and least significant portions of the result, respectively. These registers may be made transparent for asynchronous operation through the use of the Feedthrough Control (FT). The two halves of the product may be routed to a single 16-bit three-state output port via the output multiplexer control, and in addition, the LSP is connected to the Yinput port through a separate three-state buffer. The HMU16/883 utilizes independent clock signals (CLKX, CLKY, CLKL, CLKM) to latch the input operands and output Product Registers. This configuration maximizes throughput and simplifies bus interfacing. All outputs of the HMU16/883 also offer three-state control for multiplexing onto multi-use system busses.
October 1997
Features
· This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. · 16 x 16-Bit Parallel Multiplier with Full 32-Bit Product · High-Speed (45ns) Clocked Multiply Time · Low Power CMOS Operation - IC CSB = 500µA Maximum - IC COP = 7.0mA Maximum at 1MHz · HMU 16/883 is Compatible with the AM29516, LMU16, IDT7216, and the CY7C516 · Supports Two's Complement, Unsigned Magnitude and Mixed Mode Multiplication · TTL Compatible Inputs/Outputs · Three-State Outputs
Ordering Information
PART NUMBER HMU16GM-45/883 HMU16GM-60/883 TEMP. RANGE (oC) -55 to 125 -55 to 125 P ACKAGE 68 Ld CPGA 68 Ld CPGA
Functional Diagram
X0-15 TCX RND T CY Y0-1 5/P0 -15
REGISTER
REGISTER
REGISTER OEL
CL KX CL KY MULTIPLIER ARRAY
FA FT CLKM CL KL MSPSEL OEP
FORMAT ADJUST MSP REGI STER LSP REGISTER
MULTIPLEXER
P16-31/P0-1 5
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2002. All Rights Reserved 3-29
File Number
2804.2
HMU16/883
Absolute Maximum Ratings
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V Input or Output Voltage Applied . . . . . . . . GND -0.5V to VCC +0.5V ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Thermal Information
Thermal Resistance (Typical, Note 1) JA ( oC/W) JC (oC/W) CPGA Package . . . . . . . . . . . . . . . . . . 42.69 10.0 Maximum Junction Temperature. . . . . . . . . . . . . . . . . . . . . . . . 175oC Maximum Storage Temperature Range . . . . . . . . . . - 65oC to 150oC Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . . 300oC
Operating Conditions
Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V Temper ature Range . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
Die Characteristics
Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4500 Gates
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE: 1. JA is measured with the component mounted on an evaluation PC board in free air. TABLE 1. HMU16/883 DC ELECTRICAL PERFORMANCE SPECIFICATIONS Device Guaranteed and 100% Tested PARAMETER Logical One Input Voltage Logical Zero Input Voltage Output HIGH Voltage Output LOW Voltage Input Leakage Current Output or I/O Leakage Current Standby Power Supply Current Operating Power Supply Current Functional Test NOTES : 2. Interchanging of force and sense conditions is permitted. 3. Operating supply current is proportional to frequency, typical rating is 5mA/MHz. 4. Tested as follows: f = 1MHz, VIH (clock inputs) = 3.0, VIH (all other inputs) = 2.6, VIL = 0.4, VOH 1.5V, and VOL 1.5V. SYMBOL VIH VIL VOH VOL II IO ICCSB TES T CONDITIONS VCC = 5.5V VCC = 4.5V IOH = -400µA VCC = 4.5V (Note 2) IOL = +4.0mA V CC = 4.5V (Note 2) VIN = VCC or GND VCC = 5.5V VOUT = VCC or GND VCC = 5.5V VIN = VCC or GND, VCC = 5.5V, Outputs Open f = 1.0MHz, VIN = VCC or GND VCC = 5.5V (Note 3) (Note 4) GROUP A SUBGROUPS 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 TEMPERA TURE ( oC) - 55 TA 125 - 55 TA 125 - 55 TA 125 - 55 TA 125 - 55 TA 125 - 55 TA 125 - 55 TA 125 MIN 2.2 2.6 -10 -10 M AX 0.8 0.4 +10 +10 500 UNITS V V V V mA mA mA
ICCOP
1, 2, 3
- 55 TA 125
-
7.0
mA
FT
7, 8
- 55 TA 125
-
-
3-30
HMU16/883
TABLE 2. HMU16/883 AC ELECTRICAL PERFORMANCE SPECIFICATIONS Device Guaranteed and 100% Tested (NOTE 5) TEST CONDITIONS -45 GROUP A SUBGROUPS 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 (Note 6) (Note 7) 9, 10, 11 9, 10, 11 TEMPERATURE (o C ) - 55 TA 125 - 55 TA 125 - 55 TA 125 - 55 TA 125 - 55 TA 125 - 55 TA 125 - 55 TA 125 - 55 TA 125 - 55 TA 125 - 55 TA 125 MIN 18 15 15 0 M AX 70 45 25 25 25 25 MIN 20 20 20 0 -60 M AX 90 60 30 30 30 30 UNITS ns ns ns ns ns ns ns ns ns ns
PARAMETE R Unclocked Multiply Time Clocked Multiply Time X, Y, RND Setup Time Clock HIGH Pulse Width Clock LOW Pulse Width MSPS EL to Product Ou t Output Clock to P Output Clock to Y Three-S tate Enable Time Clock Low Hold Time CLKXY Relative to CLKML NOTES :
SYMBOL tMUC tMC tS tPWH tPWL tPDSEL tPDP tPDY tENA tHCL
5. AC Testing as follows: VCC = 4.5V and 5.5V. Input levels 0V and 3.0V; timing reference levels = 1.5V; output load per test load circuit, with V 1 = 4V, R 1 = 500 and C L = 40pF. 6. Transition is measured at ±200mV from steady state voltage; output loading per test load circuit with V1 = 1.5V, R1 = 500 and CL = 40pF. 7. To ensure the correct product is entered in the Output Registers; new data may not be entered into the Input Registers before the Output Registers have been clocked.
3-31
|
|
