Details, datasheet, quote on part number: TUSB214EVM
PartTUSB214EVM
Category
TitleInterface Development Tools TUSB214USB2.0HighSpd SignalCondit EvalMod
Description
CompanyTexas Instruments Inc.
DatasheetDownload TUSB214EVM datasheet
  
TUSB214EVM photo

Others parts numbering
TUSB214IRWBT: USB Interface IC USB2.0 HIGH SPEED REDRIVER
TUSB214RWBT: USB Interface IC USB2.0 HIGH SPEED REDRIVER WITH CDP

 

Features, Applications

This user's guide is for the evaluation module (EVM) of the TUSB214. The purpose of this user's guide is to facilitate an easy evaluation process of the TUSB214 USB high-speed signal conditioner from TI. The contents of this user's guide are meant to provide an overview of the TUSB214 device, which includes highlighting its key features, operating conditions, and how to set up this EVM for use in systemlevel evaluation. The construction of the TUSB214EVM also serves as a reference design that can easily be modified for any intended application. Target applications include the following: Cell phones Desktop or notebook computers Docking stations Televisions Active cables Schematic and board layout information is also included at the end of this manual.

Contents Introduction................................................................................................................... 2 Test Setup and Results..................................................................................................... 4 PCB Construction............................................................................................................ 5 List of Figures 3 TUSB214 Functional System Level Block Diagram..................................................................... 2 TUSB214EVM Board........................................................................................................ 3 TUSB214EVM Schematic.................................................................................................. 6 List of Tables 3 TUSB214 EVM Jumper Descriptions

EQ/Boost Setting Based on Cable Length............................................................................... 5 Bill of Materials............................................................................................................... 7

The TUSB214 device is a USB high-speed signal conditioner, designed to compensate for ISI signal loss in a transmission channel. The design of the TUSB214 device is agnostic to USB low and full-speed signals and does not affect FS and LS signaling. High-speed signals are compensated along with programmable DC gain, to fine-tune device performance to optimize the high-speed signals at the connector. This EVM was designed to be used as a medium connection between a USB host and a USB device. The interface to the EVM consists of a USB 3.1 Type A Receptacle and a USB 3.1 Type B Receptacle. Therefore, to connect the EVM to your system setup, you will likely need two USB 3.1 Standard Type A B cables. Your test setup should look similar to Figure 1.

USB 3.1 Host/Source (Desktop, Laptop, Docking Station, etc.) USB 3.1 Type A Receptacle
USB 7\SH $ Cable USB 3.1 Type B Receptacle [INPUT] USB 3.1 Type A Receptacle [OUTPUT]

USB 7\SH $ Cable USB 3.1 Type B Receptacle USB 3.1 Device/Sink (External Hard Drive, Thumb Drive, etc.)

Figure 1. TUSB214 Functional System Level Block Diagram
This EVM kit contains the following items: TUSB214EVM board TUSB214EVM user's guide

Description of EVM Board The TUSB214EVM is designed to provide easy evaluation of the TUSB214 device. The TUSB214EVM is also meant to serve as a reference design, to show a practical example of how to use the device in a mass-production system. Figure 2 highlights the jumpers and switch installed on this EVM, and Table 1 lists their functionality and configuration.


 

Some Part number from the same manufacture Texas Instruments Inc.
TUSB214IRWBT
TUSB214RWBT
UCC27212AQDDARQ1 Texas Instruments UCC27212/UCC27212-Q1 High Frequency High-Side & Low-Side Driver offers extended operating range all the way down to 5V which helps lower power losses. The peak output pullup and pulldown
UCC27212DPRR
UCC27212DPRT
 
0-C     D-L     M-R     S-Z