Details, datasheet, quote on part number: EVALM1099MCTOBO1
PartEVALM1099MCTOBO1
Category
TitlePower Management IC Development Tools Control Board for iMOTION™ Modular Application Design Kit (MADK). The Eval-M1-099M board requires MCETOOLV2.
DescriptionInfineon iMOTION? MADK Platforms are modular application design kits for evaluating compact and flexible 3-phase motor drives. The iMOTION MADK evaluation platform covers 115/230V motor drive applications up to 300W. Two control board options are available and a range of power boards for a modular and scalable system solution. One control board is based on a standard ARM® Cortex®-M0 Microcontroller XMC1302 with tailored motor control peripherals and MATH hardware accelerator. The other board is an iMOTION? IRMCK099 digital motion control IC with integrated Motor Control Engine (MCE).

CompanyInfineon Technologies Corporation
DatasheetDownload EVALM1099MCTOBO1 datasheet
  
EVALM1099MCTOBO1 photo

Others parts numbering
EVALM113020565DTOBO1: Power Management IC Development Tools EvalM11302EvalM10565 USBcbl,3/5pole conn
EVALM113023684ATOBO1: Power Management IC Development Tools USB Cbl,Eval-M1-1302 and Eval-M1-36-84A
EVALM113023645ATOBO1: Power Management IC Development Tools USB Cbl,Eval-M1-1302 and Eval-M1-36-45A
EVALM113020584DTOBO1: Power Management IC Development Tools EvalM11302EvalM10584 USBcbl,3/5pole conn
EVALM10584DTOBO1: Power Management IC Development Tools IRSM505084DA2,3/5ple connector on board
EVALM10565DTOBO1: Power Management IC Development Tools IRSM505065DA2,3/5ple connector on board
EVALM13684ATOBO1: Power Management IC Development Tools IRSM836-084A IPM mounted on board
EVALM13645ATOBO1: Power Management IC Development Tools IRSM836-045A IPM mounted on board
EVALM11302TOBO1: Development Boards & Kits - ARM XMC1302 mount board
EVALM1CM610N3TOBO1: Power Management IC Development Tools
MCETOOLV2 NRND: Programmers - Universal & Memory Based Isolated programmer, debugger and tuner for IRMCK099M, IRMCx100 and RMCx300 series iMOTION motor control Ics

 

Features, Applications

iMOTIONTM Modular Application Design Kit About this document

Scope and purpose This application note provides an overview of the evaluation board EVAL-M1-099M including its main features, key data, pin assignments and mechanical dimensions. is an evaluation-board as part of the iMOTIONTM Modular Application Design Kit Platform. This board features and demonstrates Infineon's advanced Motion Control Engine (MCE) technology for permanent magnet motors drive over the full speed range. The evaluation board EVAL-M1-099M was developed to support customers during their first steps designing applications with running any permanent magnet motor via sensorless sinusoidal control. Important Note: EVAL-M1-099M-C is the orderable part number for the kit which contains only EVAL-M1-099M MADK Control Board. In order to program, configure and debug the motor control systems based EVAL-M1099M, an Isolated Debugger Tool MCETOOLV2 is required. MCETOOLV2 is not part of the EVAL-M1-099M-C kit and needs to be ordered separately. Intended audience This application note is intended for all technical specialists who know motor control and high power electronics converter and this board is intended to be used under laboratory conditions.

About this document....................................................................................................................... 1 Table of Contents........................................................................................................................... Safety precautions......................................................................................................... 2 Introduction.................................................................................................................. 3 Main features................................................................................................................ 4 Key data................................................................................................................................................... 5 IRMCK099 installer.................................................................................................................................. 8 Pin assignments............................................................................................................ 9 Schematics and Layout................................................................................................. 11 Schematic Overview.............................................................................................................................. 11 Current feedback................................................................................................................................... 12 AD port Input......................................................................................................................................... 13 PCB Layout............................................................................................................................................ 14 Bill of Materials EVAL-M1-099M................................................................................... 17 Reference.................................................................................................................... 19

Please read the Important Notice and Warnings at the end of this document

In addition to the precautions listed throughout this manual, please read and understand the following statements regarding hazards associated with development systems. Table 1 Precautions

Attention: The ground potential of the EVAL-M1-099M system is biased to a negative DC bus voltage potential. When measuring voltage waveform by oscilloscope, the scope's ground needs to be isolated. Failure do so may result in personal injury or death and equipment damage Attention: Only personnel familiar with the drive and associated machinery should plan or implement the installation, start-up and subsequent maintenance of the system. Failure to comply may result in personal injury and/or equipment damage. Attention: The surfaces of the drive may become hot, which may cause injury.

Attention: EVAL-M1-099M system contains parts and assemblies sensitive to Electrostatic Discharge (ESD). Electrostatic control precautions are required when installing, testing, servicing or repairing this assembly. Component damage may result if ESD control procedures are not followed. If you are not familiar with electrostatic control procedures, refer to applicable ESD protection handbooks and guidelines. Attention: A control board, incorrectly applied or installed, can result in component damage or reduction in product lifetime. Wiring or application errors such as under sizing the motor, supplying an incorrect or inadequate DC supply or excessive ambient temperatures may result in system malfunction. Attention: Remove or connect this control board from or to the power drive. Wait three minutes after removing power from the power drive to discharge the bus capacitors. Do not attempt to service the drive until the bus capacitors have discharged to zero. Failure do so may result in personal injury or death. Attention: EVAL-M1-099M system is shipped with packing materials that need to be removed prior to installation. Failure to remove all packing materials which are unnecessary for system installation may result in overheating or abnormal operating condition.

The EVAL-M1-099M evaluation board is a part of the iMOTIONTM Modular Application Design Kit for drives (iMOTIONTM MADK). In order to run a motor, the mating power board is required to interface this evaluation board. The MADK platform is intended to use various power stages with different control boards. These boards can easily be interfaced through the 20 pins iMOTIONTM MADK-M1 or the 30 pins iMOTIONTM MADK-M3 interface connector. This board is equipped with 20 pins connector and for motor control only. This evaluation board is designed to give comprehensible solutions of sensorless control of permanent magnet motors over the full speed range. It consists of IRMCK099M Motor Control IC, capable of 3-phase and three types of 2-phase modulation, JTAG and UART interface which are isolated via opto-isolation box (MCETOOLV2), and needs a single 3.3V supply. Required Isolation Box MCETOOLV2 is not part of the EVAL-M1-099M-C kit and needs to be ordered separately. For details of the isolation box please refer to its Application Note. The EVAL-M1-099M evaluation board is available from Infineon and its distribution partners. The features of this board are described in the design feature chapter of this document, whereas the remaining paragraphs provide information to enable the customers to copy, modify and qualify the design for production according to their own specific requirements. Environmental conditions were considered in the design of the EVAL-M1-099M. The design was tested as described in this document but not qualified regarding safety requirements or manufacturing and operation over the whole operating temperature range or lifetime. The boards provided by Infineon are subject to functional testing only. Evaluation boards are not subject to the same procedures as regular products regarding Returned Material Analysis (RMA), Process Change Notification (PCN) and Product Discontinuation (PD). Evaluation boards are intended to be used under laboratory conditions by technical specialists only. Figure 1 shows the evaluation board EVAL-M1-099M. This document explains the features and details of this board as well as control IC which is IRMCK099.


 

Some Part number from the same manufacture Infineon Technologies Corporation
EVALM113020565DTOBO1 Infineon iMOTION? MADK Platforms are modular application design kits for evaluating compact and flexible 3-phase motor drives. The iMOTION MADK evaluation platform covers 115/230V motor drive applications
EVALM113023684ATOBO1
EVALM113023645ATOBO1
EVALM113020584DTOBO1
EVALM10584DTOBO1
EVALM10565DTOBO1
EVALM13684ATOBO1
EVALM13645ATOBO1
EVALM11302TOBO1
EVALM1CM610N3TOBO1
MCETOOLV2 NRND
 
0-C     D-L     M-R     S-Z