Details, datasheet, quote on part number: MXC6255XC
PartMXC6255XC
Category
TitleAccelerometers Accelerometer, 2 Axis, Low cost, WLP
Description

MEMSIC MXC6255XC/U Digital Thermal Orientation Sensor (DTOS) Accelerometers are fully-integrated orientation sensors that operate on MEMSIC's patented MEMS-thermal technology and are built using a standard 0.18um CMOS process. These DTOS contain no moving parts (such as a ball) and thus eliminate field-reliability and repeatability issues associated with competitive products.  The "click" sounds typically heard in ball based orientation sensors is also eliminated. Shock survival is greater than 50,000g. DTOS detects four orientations, shake, and shake direction and provides X/Y axis acceleration signals with very low 0g offset. An I2C interface is used to communicate with this device and an interrupt pin (INT) is provided for shake and orientation. The DTOS also has a power down enabled through the I2C interface.



CompanyMemsic
DatasheetDownload MXC6255XC datasheet
Quote
Find where to buy
 
  
MXC6255XC photo

Others parts numbering
MXC6255XU: Accelerometers Accelerometer, 2 Axis, Low cost
MXC6255XU-B: Acceleration Sensor Development Tools Proto Board, Accelerometer, 2 Axis, Low cost

 

Features, Applications

Chip Scale Packaged Digital Thermal Orientation Sensing Accelerometer

2010 MEMSIC, Inc. One Technology Drive, Suite 325 Andover, MA 01810, USA Tel: Fax: www.memsic.com Information furnished by MEMSIC is believed to be accurate and reliable. However, no responsibility is assumed by MEMSIC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of MEMSIC. Information presented in this document is the property of MEMSIC, Inc., is considered proprietary, and is not to be reproduced without the specific written permission of MEMSIC, Inc.

Features

Fully Integrated Thermal Accelerometer X/Y Axis, 8 bit, Acceleration A/D Output 2g) Chip Scale Package (1.18x1.705x0.955mm) 4-position Orientation Detection Shake Detection with Interrupt Programmable Shake Threshold Shake Direction Detection I C Interface Power Down Mode Shock Survival Greater than 50,000 g Operating Supply Voltage from to 5.5V with 1.8V compatible IO Produces no Mechanical Sounds ("click")

The MEMSIC Digital Thermal Orientation Sensor is the world's first fully-integrated orientation sensor also with chip scale package. Its operation is based on our patented MEMS-thermal technology and is built using a standard 0.18um CMOS process. DTOS contains no moving parts (such as a ball) and thus eliminates field-reliability and repeatability issues associated with competitive products. It also eliminates the "click" sounds typically heard in ball based orientation sensors. Shock survival is greater than 50,000g. DTOS detects four orientations, shake and shake direction. In addition, it provides X/Y axis acceleration signals with very low 0g offset. I C interface is used to communicate with this device and an interrupt pin (INT) is provided for shake and orientation. The DTOS also has a power down enabled through the I C interface.

Cell Phones Digital Still Cameras (DSC) Digital Video Cameras (DVC) LCD TV Toys MP3, MP4 Players Household Safety: Fan Heaters Halogen Lamps Iron Cooling Fans The MXC6255XC is packaged in a hermetically sealed, wafer level chip scale package (WLCSP, 0.955mm) , the product is RoHS compatible and operates over -20~70 temperature range. Figure 1

2010 MEMSIC, Inc. One Technology Drive, Suite 325 Andover, MA 01810, USA Tel: Fax: www.memsic.com Information furnished by MEMSIC is believed to be accurate and reliable. However, no responsibility is assumed by MEMSIC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of MEMSIC. Information presented in this document is the property of MEMSIC, Inc., is considered proprietary, and is not to be reproduced without the specific written permission of MEMSIC, Inc.

Pin 1 Name I2C SCL Description This pin is the serial clock line for the I2C interface. Since the MXC6255XC only operates as a slave device, this pin is always an input. 4 NC GND INT During normal operation, this pin must be left floating. This is the ground pin for the MXC6255XC. This pin is the MXC6255XC interrupt output. The logic level on this pin reflects the state of the INT bit in the STATUS register. INT is set when the orientation differs from the last orientation read by the processor, or a shake event is detected. INT is cleared upon reading of the STATUS register.

This pin is the serial data line for the I2C interface. is an I/O pin that functions as an input during a write, and an output during a read from the MXC6255XC.

This is the power supply input. The DC voltage should be between 2.5 and 5.5 volts.

*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; the functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Parameter (Units) Operating Voltage Range (V) VIO(I C interface)(V) In power-up mode Supply Current (mA) In power-down mode Turn-On Time (ms) Turn-off Time (ms) Operating Temperature Range VDD Rise Time (ms)

Notes: 1 All specifications are at 3V and room temperature unless otherwise noted. 2 Time to obtain valid data after existing power-down mode. 3 Maximum allowable power supply rise time from to 2.5V (minimum). Slower VDD rise time may cause erroneous data retrieval from OTP memory at power-up.

Parameter (Units) Measurement Range (g) Alignment Error Sensitivity Error Sensitivity (LSB/g) Sensitivity Drift Over Temperature Zero g Offset Bias Level (mg) Zero g Offset Temperature coefficient (mg/) 3dB Signal Bandwidth (Hz) Conditions X/Y Axis X/Y Axis X/Y Axis X/Y Axis Delta from X/Y Axis (25 ) X/Y Axis Minimum Typical Maximum

Notes: 1 All specifications are at 3V and room temperature unless otherwise noted.

2010 MEMSIC, Inc. One Technology Drive, Suite 325 Andover, MA 01810, USA Tel: Fax: www.memsic.com Information furnished by MEMSIC is believed to be accurate and reliable. However, no responsibility is assumed by MEMSIC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of MEMSIC. Information presented in this document is the property of MEMSIC, Inc., is considered proprietary, and is not to be reproduced without the specific written permission of MEMSIC, Inc.


 

Some Part number from the same manufacture Memsic
MXC6255XU

MEMSIC MXC6255XC/U Digital Thermal Orientation Sensor (DTOS) Accelerometers are fully-integrated orientation sensors that operate on MEMSIC's patented MEMS-thermal technology and are built using a standard

MXC6255XU-B
Eval Kit DMU380ZA-200 Specifications: Product: Evaluation Kits ; Type: IMUs - Inertial Measurement Units ; Tool Is For Evaluation Of: IMU380ZA ; Operating Supply Voltage: 3 V to 5.5 V ; Packaging: Bulk
Eval Kit DMU380ZA-400
MFC2030BP1N1

MEMSIC MFC2000 Digital MEMS Gas Flow Sensor, based on MEMSIC's proprietary CMOS technology for thermal mass flow sensing, can measure up to 70 SLM bi-directional flow rate with 3.0% accuracy. The sensing

 
0-C     D-L     M-R     S-Z