Log in
Register
Details, datasheet, quote on part number: TP1.5KE12A
PartTP1.5KE12A
Category
TitleTVS DIODE 10.2WVM 16.7VC AEC-Q
Description

Littelfuse introduces TVS diodes designed specifically to protect sensitive electronic equipment from voltage transients induced by load dump and other transient voltage events. The AEC­Q101 qualified TP1.5KE series automotive transient voltage suppression (TVS) diodes offer 1500 W peak pulse power dissipation ratings in a standard DO-201 axial-lead package. Its high peak pulse power dissipation rating helps the power systems into which it is designed pass surge tests outlined in the ISO7637-2 international standard, which is widely used in the automotive industry as the basis for transient specifications.



CompanyLittelfuse
DatasheetDownload TP1.5KE12A datasheet
  
TP1.5KE12A photo

Others parts numbering
TP1.5KE12CA
TP1.5KE18A: TVS DIODE 15.3WVM 25.2VC AEC-Q
TP1.5KE18CA
TP1.5KE22A: TVS DIODE 18.8WVM 30.6VC AEC-Q
TP1.5KE22CA
TP1.5KE27A: TVS DIODE 23.1WVM 37.5VC AEC-Q
TP1.5KE27CA
TP1.5KE30CA: TVS DIODE 25.6WVM 41.4VC AEC-Q
TP1.5KE33A: TVS DIODE 28.2WVM 45.7VC AEC-Q
TP1.5KE33CA
TP1.5KE36A: TVS DIODE 30.8WVM 49.9VC AEC-Q
TP1.5KE36CA
TP1.5KE43A: TVS DIODE 36.8WVM 59.3VC AEC-Q
TP1.5KE43CA
TP1.5KE13A: TVS DIODE 11.1WVM 18.2VC AEC-Q
TP1.5KE15A: TVS DIODE 12.8WVM 21.2VC AEC-Q
TP1.5KE15CA
TP1.5KE16A: TVS DIODE 13.6WVM 22.5VC AEC-Q
TP1.5KE20A: TVS DIODE 17.1WVM 27.7VC AEC-Q

 

Features, Applications

The 1.5KE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.

Features Bi-directional 1500W peak pulse capability at 10/1000s waveform, repetition rate (duty cycles):0.01% Glass passivated chip junction in DO-201 Package Fast response time: typically less than 1.0ps from 0 Volts to BV min Excellent clamping capability Typical failure mode is short from over-specified voltage or current Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4cI EC-61000-4-2 ESD 30kV(Air), 30kV (Contact)E SD protection of data lines in accordance with IEC 61000-4-2E FT protection of data lines in accordance with IEC 61000-4-4 Low incremental surge resistance Typical IR less than 1A when VBR min>12V High temperature to reflow soldering guaranteed: 0.375" ,(9.5mm) lead length, 5 lbs., (2.3kg) tension VBR @ TJ= (1+T x (TJ - 25)) (T:Temperature Coefficient, typical value is 0.1%) Plastic package is flammability rated V-0 per Underwriters Laboratories Matte tin leadfree plated Halogen free and RoHS compliant Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01)

Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted)

Parameter Peak Pulse Power Dissipation by 10/1000s Test Waveform (Fig.2) (Note 1), (Note 4) Steady State Power Dissipation on Infinite Heat Sink at TL=75C Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only (Note 3) Operating Junction and Storage Temperature Range Typical Thermal Resistance Junction to Lead Typical Thermal Resistance Junction to Ambient Symbol PPPM PD IFSM TJ , TSTG RJL RJA Value 15 75 Unit C C/W

Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. < 3.5V for single die parts and VF< 5.0V for stacked-die parts. 4. The PPPM of stacked-die parts is 2kW and please contact littelfuse for the detail stacked-die parts.

Applications TVS devices are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Additional Infomarion

2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15

F For bidirectional type having of 10 volts and less, the IR limit is double. For parts without A, the VBR 10% and is 5% higher than with A parts.

Peak Pulse Power Dissipation Max power dissipation Stand-off Voltage Maximum voltage that can be applied to the TVS without operation Breakdown Voltage Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current measured at VR Forward Voltage Drop for Uni-directional

Ratings and Characteristic Curves (T =25C unless otherwise noted)

 

Some Part number from the same manufacture Littelfuse
TP1.5KE12CA

Littelfuse introduces TVS diodes designed specifically to protect sensitive electronic equipment from voltage transients induced by load dump and other transient voltage events. The AEC­Q101 qualified

TP1.5KE18A
TP1.5KE18CA
TP1.5KE22A
TP1.5KE22CA
TP1.5KE27A
TP1.5KE27CA
TP1.5KE30CA
TP1.5KE33A
TP1.5KE33CA
TP1.5KE36A
TP1.5KE36CA
TP1.5KE43A
TP1.5KE43CA
TP1.5KE13A
TP1.5KE15A
TP1.5KE15CA
TP1.5KE16A
TP1.5KE20A
 
0-C     D-L     M-R     S-Z